[ML-General] Joiner

[Kirk D Mccann]

>From that I read thats an ok alternate if you cant find a Gauge to
accurately measure it.  good to know some I know uses that method and has
had positive results with it.

Thanks

On Tue, Feb 20, 2018 at 8:10 AM, Wesley Swift <wesleyswift2 at gmail.com>
wrote:

> I always set joiner blades with a straight edge.   First, use the straight
> edge to check that the blade edges are sharpened straight.  Offset any
> small notches so they don't form a groove.  Grind out any significant
> notches in the blades or get new ones.
>
> I then set and level them to the out table. Set the straight edge on the
> out table extended over the blades.   When you rock the blades back and
> forth, they should barely touch the straight edge all the way across.
>
> On Feb 20, 2018 12:19 AM, "Kirk D Mccann" <kirk.mccann at gmail.com> wrote:
>
>> I stopped by today and it looks like those blades need to be sharpened or
>> replaced.
>>
>> Do you know where I could find a Oneway Multi Gauge so I can make sure
>> the blades are level with the out table?  Or at least something with a good
>> level of accuracy.
>>
>> -Kirk
>>
>> On Mon, Feb 19, 2018 at 12:55 AM, Tyler Crumpton <
>> tyler.crumpton at gmail.com> wrote:
>>
>>> It may need a new blade, IIRC. I remember hearing complaints of it
>>> leaving scars in the wood. I believe it's an 8" joiner.
>>>
>>> Tyler Crumpton
>>> tyler.crumpton at gmail.com
>>>
>>> On Mon, Feb 19, 2018 at 12:25 AM, Kirk D Mccann <kirk.mccann at gmail.com>
>>> wrote:
>>>
>>>> By not in the greatest shape do you mean out of alignment or is the
>>>> in/outfeed table(s) damaged?
>>>>
>>>> Any idea how wide it is?
>>>>
>>>> Thanks,
>>>> Kirk
>>>>
>>>> On Mon, Feb 19, 2018 at 12:11 AM, Tyler Crumpton <
>>>> tyler.crumpton at gmail.com> wrote:
>>>>
>>>>> We have an older joiner that is not in the greatest shape, but we do
>>>>> also have a 12" planer in good condition. Someone was even using it just
>>>>> today!
>>>>>
>>>>> Cheers,
>>>>> Tyler
>>>>>
>>>>> Tyler Crumpton
>>>>> tyler.crumpton at gmail.com
>>>>>
>>>>> On Mon, Feb 19, 2018 at 12:04 AM, Kirk D Mccann <kirk.mccann at gmail.com
>>>>> > wrote:
>>>>>
>>>>>> Does anyone know if the shop has a joiner?  I looked through the wiki
>>>>>> and didnt see one but I figured there had to be one there.
>>>>>>
>>>>>> -Kirk
>>>>>>
>>>>>> _______________________________________________
>>>>>> This is the general mailing list.
>>>>>> This list is for public discussion about Makers Local and related
>>>>>> activities.
>>>>>> To stop receiving mail from this list, write to
>>>>>> general-leave at lists.makerslocal.org.
>>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> This is the general mailing list.
>>>>> This list is for public discussion about Makers Local and related
>>>>> activities.
>>>>> To stop receiving mail from this list, write to
>>>>> general-leave at lists.makerslocal.org.
>>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> This is the general mailing list.
>>>> This list is for public discussion about Makers Local and related
>>>> activities.
>>>> To stop receiving mail from this list, write to
>>>> general-leave at lists.makerslocal.org.
>>>>
>>>
>>>
>>> _______________________________________________
>>> This is the general mailing list.
>>> This list is for public discussion about Makers Local and related
>>> activities.
>>> To stop receiving mail from this list, write to
>>> general-leave at lists.makerslocal.org.
>>>
>>
>>
>> _______________________________________________
>> This is the general mailing list.
>> This list is for public discussion about Makers Local and related
>> activities.
>> To stop receiving mail from this list, write to
>> general-leave at lists.makerslocal.org.
>>
>
> _______________________________________________
> This is the general mailing list.
> This list is for public discussion about Makers Local and related
> activities.
> To stop receiving mail from this list, write to general-leave at lists.
> makerslocal.org.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.makerslocal.org/pipermail/general/attachments/20180223/76e7865b/attachment.html>